Router · TOTOLINK

TOTOLINK router login, restart, firmware and port forwarding

TOTOLINK makes Wi-Fi routers, from the N and A Series to the Wi-Fi 6 X Series. You manage them in a browser. TOTOLINK’s help pages are model-group FAQs, so this guide says which group each path belongs to.

Sign in
itotolink.net or 192.168.0.1
Password
Current models ask only for a password, which is admin until you change it. Older models ask for a user name too: admin in both boxes. The sticker underneath shows the login address and the factory Wi-Fi name, usually TOTOLINK_ plus the model.
Models
X6000R, X5000R, X30, X18, A3300R, A720R, N350RT, N200RE_V5, A3002RU, A950RG

Checked 10 November 2026. Paths come from TOTOLINK’s FAQ pages, which don’t name firmware versions. “Current models” means the 2023 FAQs for the X6000R, X5000R, X60, X30, X18, T6, T8, A3300R, A720R, N350RT, N200RE_V5, NR1800X and LR350. “A3002RU group” means the N100RE, N150RT, N200RE, N210RE, N300RT, N302R Plus, A702R, A850R and A3002RU. “N600R group” means the N600R, A800R, A810R, A3100R, T10, A950RG and A3000RU. Those two older groups’ pages date from 2018–2020. TOTOLINK documents fewer screens for current models, so several steps are older-group only.

Sign in to the TOTOLINK

Factory default. admin. The factory Wi-Fi is unencrypted, so set a Wi-Fi password and a new login password in Quick Setup.

  1. Connect your Mac to the router’s Wi-Fi, or by Ethernet to a LAN port, not the WAN port.

  2. Open http://itotolink.net, or the address on the bottom label.

  3. Enter admin and click LOGIN.

  4. The first time, click Quick Setup and follow it. It asks for a new login password.

  5. On older models, click Advanced Setup at the top right for the full menus.

Some older models, such as the A1004 and N300RA, use 192.168.1.1 and a Setup Tool icon. Forgotten the password? With the power on, hold RST for 8–10 seconds, until all the lights come on. That erases your settings.

Change the login password on older models

  1. In the A3002RU group, open System › Password Settings.

  2. In the N600R group, open Management › Administrator Setting.

  3. Enter the old password, then the new one.

Restart it properly

TOTOLINK’s FAQs don’t describe a restart button in the web interface. Its spec page for the BE3600R lists Reboot on the home screen.

  1. Turn the router off at the power, then on again.

  2. Wait about half a minute. The SYS light should flash; that’s normal.

A SYS light that stays on or off after a restart means a fault, according to TOTOLINK.

Schedule a restart on older models

  1. Make sure NTP is on under System › Time Zone Setting or Management › Time Setting.

  2. In the A3002RU group, open System › Reboot Schedule.

  3. In the N600R group, open Management › Reboot Schedule.

  4. Set the time the router should restart.

Update the firmware

Firmware is a manual download. Spec pages list Upgrade Firmware under Tools on the X6000R and BE3600R, without steps.

  1. Find the hardware version on the bar-code sticker. V1.1 means hardware V1.

  2. On www.totolink.net, open your model’s Download tab and get the firmware for that hardware version.

  3. Unzip it. The right file name ends in web or bin.

  4. Connect by Ethernet. TOTOLINK says not to upgrade over Wi-Fi.

  5. Open System › Upgrade Firmware (A3002RU group) or Management › Upgrade Firmware (N600R group).

  6. Select the local file and click Upgrade. The router restarts by itself after a few minutes.

Don’t power off or close the browser during the upgrade. TOTOLINK says to reset the router with RST afterwards, so note your settings first. The wrong firmware can damage it, and TOTOLINK’s site is for models sold outside mainland China, Taiwan and South Korea.

The maker’s firmware download page

See connected devices

TOTOLINK documents no connected-device list page. On current models, the QoS rule form has a magnifier icon that shows connected devices.

Keep the same address for one device

  1. On current models, open Advanced Settings › Network Settings › IP/MAC Address Binding.

  2. In the A3002RU group, open Network › LAN Settings and click Set Static DHCP.

  3. Tick Enable Static DHCP, enter the IP and MAC addresses, then click Apply.

UPnP and port forwarding

TOTOLINK’s spec pages list UPnP under Tools on the X6000R and BE3600R, but its FAQs give no steps. They don’t say whether it’s the IGD profile, and don’t mention NAT-PMP or a separate status switch.

Forward only what an app needs. TOTOLINK warns that a DMZ host is fully exposed to the internet. On current models, DMZ host is under Advanced Settings › NAT. Neither works if your provider gives you a private WAN address.

Forward a port instead

The X6000R’s spec lists Virtual Server (Port Forwarding) under NAT; the steps below are for older models.

  1. In the A3002RU group, open Firewall › Virtual Server and click Add.

  2. In the N600R group or the A3002RU group’s old interface, open Firewall › Port Forwarding and click Enable.

  3. Enter the external and internal ports, the protocol and the device’s IP address.

  4. Click Apply or Add, and check the rule appears in the list.

Prioritise calls and gaming

TOTOLINK’s QoS caps each device’s speed. It doesn’t prioritise one device over another.

  1. On current models, find the QoS switch in the basic settings and turn it on.

  2. Enter your total upload and download bandwidth.

  3. In the rule list, click Add and the magnifier icon, then pick a device.

  4. Enter its upload and download limits and add the rule.

Older models

  1. Open QoS (A3002RU group) or Qos › Qos (N600R group) and select Enable.

  2. Enter the total bandwidth, then a device’s IP Address and limits, and click Apply.

2.4 and 5 GHz, and the channel

Dual-band models run 2.4 GHz and 5 GHz at once. TOTOLINK notes that 2.4 GHz reaches farther, while 5 GHz has more channels and less interference.

  1. On older models, click Advanced Setup.

  2. Open Wireless › Basic Settings, or Wireless 2.4GHz and Wireless 5GHz on dual-band models.

  3. Change the SSID, encryption and password, then click Apply.

Change the channel on older models

  1. In the N600R group, choose the Channel Number under Wireless › Basic Settings.

  2. On the A3002RU, A702R and A850R, it’s under Wireless 2.4GHz › Advanced Settings.

  3. Click Apply.

Mesh: which node a device uses

Mesh is documented for the X6000R, which uses EasyMesh, and the older T10. The T6, T8, X18, X30 and X60 are sold as kits with units already bound.

  1. Power on both X6000Rs. Connect one to the internet as the main unit.

  2. On the main unit’s page, click EasyMesh, then Mesh Settings.

  3. Turn on the mesh switch, select the controller role and apply.

  4. Click Start MESH, and hold the second unit’s MESH button for 2 seconds.

  5. Its light changes from flashing red to steady blue when paired.

The X5000R has separate EasyMesh firmware on its download page. If a kit’s main unit is lost, TOTOLINK’s unbinding page is at 192.168.0.212; this resets the unit.

T10 kit

  1. Place the satellites within a metre of the master and power them on.

  2. Hold the master’s T button for about 3 seconds, until its light blinks red and orange.

  3. Wait about a minute for steady green lights on the satellites, then move them.

Guest network

Older FAQs call this Multiple SSID and don’t say whether guests are kept apart from your devices. The X6000R’s spec lists Guest Network under Wireless, without steps.

  1. In the N600R group, open Wireless › Multiple APs and select Enable.

  2. In the A3002RU group, open Wireless 2.4GHz › Multiple SSID 1 and select Enable.

  3. Enter an SSID and password, then click Add or Apply.

  4. On a dual-band A3002RU group model, repeat under Wireless 5GHz.

DNS settings

TOTOLINK documents no way to change the DNS servers the router uses or hands out. Set DNS on the Mac instead. Dynamic DNS is at Advanced Settings › Network › DDNS on current models.

Connection status and logs

  1. On current models, look under the advanced system status page for the WAN address.

  2. On older models, click Advanced Setup; System Status shows the full firmware version.

System log on older models

  1. Open System › System Log (A3002RU group) or Management › System Log (N600R group).

  2. If it’s off, turn the log on and click Apply.

  3. Click Refresh to see the latest entries.

Manuals and downloads

Links go to the maker’s own pages.

Questions

Is the RST button the same as WPS?

On some models it’s one RST/WPS button. A one-second press starts WPS; holding it for more than five seconds resets the router.

Mac problems on this network

Fixes for what Mac users most often hit on home routers and mesh systems.

Mac drops Wi-Fi or sticks to a far node on mesh Wi-FiOn a mesh network, your Mac drops when it moves between nodes, or stays on a distant one. See how Macs roam and which router settings to change.Guide →Mac Wi-Fi keeps disconnectingYour Mac drops Wi-Fi again and again, not only after sleep. Record when the drops happen, then check the router, roaming, interference and network software.Guide →Mac won't connect to a WPA3 or Wi-Fi 7 routerYour Mac can't join, or keeps dropping, after the router moved to WPA3 or Wi-Fi 7. Check the security mode, PMF and MLO, and the saved network.Guide →Mac can't see or join a 6 GHz Wi-Fi networkYour Mac never uses 6 GHz, or can't find the 6 GHz network. Check Mac support, Wi-Fi 6E mode, WPA3 and the router's 6 GHz settings.Guide →AirPlay or AirPrint stopped working after a new router or meshYour Mac no longer finds the Apple TV, speaker or printer after a router or mesh change. Check the router settings that stop Bonjour discovery, brand by brand.Guide →Wi-Fi printer shows Offline on a MacThe printer is on and connected to Wi-Fi, but the Mac says Offline or Printer not connected. Find the cause and re-add the printer so that it stays online.Guide →Double NAT: a mesh system behind your provider’s routerA mesh system behind your provider's router can create double NAT. See what it breaks, how to spot it from a Mac, and when to use bridge or passthrough mode.Guide →iCloud Private Relay and your router’s security or parental controlsPrivate Relay stops working at home, or your router's security and parental controls stop covering the Mac. See which router features conflict and what to change.Guide →

Sources

Checked on 10 November 2026.

See what your router can’t tell you

Kilobat is a Mac menu-bar app that watches the network from your side: which app is using it, whether the Wi-Fi, the router or the provider is slow, and why a call froze.

Download for Mac ↓
brew install seifip/kilobat/kilobat