Provider box · Jazztel

Jazztel router login, restart, UPnP and guest Wi-Fi

Jazztel supplies Livebox fibre routers, with older ZTE models still in many homes. You manage both in a browser at 192.168.1.1. The menus are in Spanish on the Livebox and in English on the ZTE routers.

Sign in
livebox or 192.168.1.1
Password
On a Livebox the user name is admin. Unless you changed it, the password is the Clave Wi-Fi (Wi-Fi key) on the sticker under the router, or on the back of a Livebox 6s.
Models
Livebox 6s, Livebox 6, Livebox 6+, Livebox Fibra, ZTE F680, ZTE F660, ZTE H298N, ZTE H218N

Checked 10 November 2026. Paths come from Jazztel’s own help pages. Livebox 6 and 6+ are the main reference; Livebox 6s and Livebox Fibra pages show the same menus. On the latest Livebox software some Wi-Fi options moved to Configuración avanzada (Advanced settings). ZTE steps apply to the F680, F660, H298N and H218N, and menus can vary with software version. Jazztel publishes no firmware version list.

Sign in to the Jazztel router (Livebox and ZTE)

Factory default. ZTE routers only: jazztel / jazztel or admin / admin, depending on its age. Jazztel recommends changing it at first sign-in, under Administration › User Management.

  1. Connect your Mac to the router with an Ethernet cable or over its Wi-Fi network.

  2. Open http://livebox or http://192.168.1.1 in your browser. On a Livebox Fibra you can also use http://liveboxfibra.

  3. Type admin as the user and the Wi-Fi key from the sticker as the password.

  4. Click Acceso (Sign in), shown as Entrar on some Livebox Fibra software.

Forgotten a password you set? Push a pointed object into the Reset hole at the back: 5 seconds on a Livebox 6 or 6s, 10 seconds on a Livebox Fibra with the router on. The sticker password works again, but every setting is erased. The fibre (ONT) password is a different key.

Change the Livebox admin password

  1. Open the Configuración avanzada (Advanced settings) tab.

  2. Click Administración in the left-hand column.

  3. Enter the Contraseña actual (Current password), then the new one twice.

  4. Click Guardar (Save). The user name stays admin.

Restart it properly

Jazztel’s advice for a stuck connection is to switch the Livebox off and on.

  1. Press the ON/OFF button at the back to switch the Livebox off.

  2. Press it again to switch the Livebox back on.

  3. Wait up to 3 minutes for the Internet light to turn steady green.

Don’t use the Reset hole to restart: it erases your settings.

Schedule a restart

Do this with the TV decoder switched off.

  1. Sign in and open the Información y diagnóstico (Information and diagnostics) tab.

  2. Click Reinicio (Restart).

  3. Set automatic restart to Sí (Yes).

  4. In Reiniciar cada (Restart every), enter the number of nights, such as 7.

  5. Click Guardar (Save). The restart happens between 3 and 4 AM.

Update the firmware

Jazztel documents no manual software update or version page for the Livebox. ZTE routers show the firmware version after you sign in, but Jazztel documents no update.

See connected devices

  1. Sign in and open the Mi red local (My local network) tab.

  2. Click Dispositivos conectados (Connected devices) for a map of wired and Wi-Fi devices.

  3. Click a device to rename it, change its icon or restrict its internet access.

  4. Open Dispositivos desconectados (Disconnected devices) for those seen before but offline now.

See Wi-Fi details or a list with addresses

  1. Open Wi-Fi › Equipos Wi-Fi (Wi-Fi devices) to see band, RSSI and current speed.

  2. For names, IP and MAC addresses, open Configuración avanzada › Configuración de la red › DHCP (Advanced settings › Network settings › DHCP).

Give a device a fixed address

  1. Open Configuración avanzada › Configuración de la red › DHCP.

  2. Under Dirección IP estática (Static IP address), pick the device and enter the address.

  3. Click Añadir (Add).

UPnP and port forwarding

Jazztel’s Livebox pages name a UPnP IGD switch, and say UPnP is on by default on the Livebox Fibra and ZTE routers. Apps that support it open their own ports.

  1. Sign in and open the Configuración avanzada (Advanced settings) tab.

  2. Click Configuración de la red (Network settings) on the left.

  3. Open the UPnP tab in the middle of the page.

  4. Check that Habilitar UPnP IGD (Enable UPnP IGD) is ticked.

With UPnP on, any app or device on your network can open ports without asking, and malware can too. Turn it off if nothing needs it. Jazztel documents no separate switch for sharing status over UPnP.

UPnP on ZTE routers

  1. Sign in and click Application, then UPnP.

  2. Check that Enable is ticked.

Open a port by hand on a Livebox

  1. Open Configuración avanzada › Configuración de la red › NAT/PAT.

  2. Under Personalizar reglas (Custom rules), pick the Aplicación / servicio (Application / service).

  3. Fill in Puerto interno (Internal port) and Puerto externo (External port); write a range as first-last.

  4. Choose the Protocolo (TCP, UDP or both) and the Dispositivo (Device).

  5. Click Añadir (Add).

Open a port by hand on a ZTE router

  1. Open Application › Application List and click Click here to add an application.

  2. Enter an Application Name, the Protocol and the port fields, then click Add.

  3. Open Port Forwarding (Application List).

  4. Enter the device’s LAN Host IP Address, choose the rule under AppName and click Add.

NAT-PMP

Jazztel documents no NAT-PMP setting.

Prioritise calls and gaming

Jazztel documents no QoS or device-priority setting. On a Livebox you can only block a device or limit its internet hours under Mi red local › Dispositivos conectados.

2.4 and 5 GHz, and the channel

Wi-Fi Inteligente (Smart Wi-Fi) gives you one network name for 2.4 GHz and 5 GHz; the router picks the band and channel. A secondary network uses a single band.

  1. Sign in and open Wi-Fi › Wi-Fi principal (Main Wi-Fi).

  2. On the latest software, open Configuración avanzada › Configuración del Wi-Fi instead and confirm with OK.

  3. Click Ver (Show) to open the secondary networks.

  4. Turn on the 2.4 GHz or 5 GHz network, and give it a name and password.

  5. Click Guardar (Save).

Repeaters don’t relay secondary networks, so connect them to the main Wi-Fi Inteligente network.

Pair a 2.4 GHz-only gadget

  1. On a Livebox 6, hold the WPS button for 5 seconds; the Wi-Fi light flashes white and green.

  2. Within 15 minutes, pair the gadget using the network name and key on the left of the label.

Change the channel

Jazztel documents no manual channel setting on the Livebox; Wi-Fi Inteligente picks the channel. It says the ZTE menu can change channels but gives no path.

Mesh: which node a device uses

Jazztel’s Wi-Fi Premium repeater joins the Livebox in one Wi-Fi Inteligente network, so you don’t pick the router or repeater by hand.

  1. Connect the repeater to the main Wi-Fi Inteligente network, not a secondary one.

  2. Sign in and open Wi-Fi › Equipos Wi-Fi (Wi-Fi devices).

  3. Check the group listing devices connected through a repeater.

  4. Read the Banda (Band) column; Rep-5G or Rep-2.4G means the device uses a repeater.

Guest network

  1. Sign in and open Wi-Fi › Wi-Fi de invitados (Guest Wi-Fi).

  2. Use the Activar/desactivar (On/off) button to turn the guest network on.

  3. Set the Nombre (SSID) (Network name) and the Clave Wi-Fi (Wi-Fi key).

  4. Set the Temporizador (Timer) to turn the network off after a few hours.

  5. Click Guardar (Save).

Guests get internet access but can’t reach your other devices. Jazztel’s repeaters don’t relay guest Wi-Fi.

DNS settings

Jazztel documents no setting for the DNS servers the router uses or hands out. Set DNS on the Mac instead.

Connection status and logs

Jazztel documents the router’s lights rather than a line or event log page.

  1. Look at the Internet light on the Livebox. Steady green means you’re online.

  2. Flashing green means it is still connecting. Wait 3 minutes, then switch the Livebox off and on.

  3. Steady white means the fibre password (ONT password) is missing or wrong.

  4. Flashing white means the fibre isn’t connected, so check the fibre cable.

Manuals and downloads

Links go to the maker’s own pages.

Questions

Which password opens the Jazztel router settings?

On a Livebox, the user is admin and the password is the Wi-Fi key on the sticker, unless you changed it. ZTE routers use jazztel / jazztel or admin / admin, depending on their age.

Mac problems on this network

Fixes for what Mac users most often hit on home routers and mesh systems.

Mac drops Wi-Fi or sticks to a far node on mesh Wi-FiOn a mesh network, your Mac drops when it moves between nodes, or stays on a distant one. See how Macs roam and which router settings to change.Guide →Mac Wi-Fi keeps disconnectingYour Mac drops Wi-Fi again and again, not only after sleep. Record when the drops happen, then check the router, roaming, interference and network software.Guide →Mac won't connect to a WPA3 or Wi-Fi 7 routerYour Mac can't join, or keeps dropping, after the router moved to WPA3 or Wi-Fi 7. Check the security mode, PMF and MLO, and the saved network.Guide →Mac can't see or join a 6 GHz Wi-Fi networkYour Mac never uses 6 GHz, or can't find the 6 GHz network. Check Mac support, Wi-Fi 6E mode, WPA3 and the router's 6 GHz settings.Guide →AirPlay or AirPrint stopped working after a new router or meshYour Mac no longer finds the Apple TV, speaker or printer after a router or mesh change. Check the router settings that stop Bonjour discovery, brand by brand.Guide →Wi-Fi printer shows Offline on a MacThe printer is on and connected to Wi-Fi, but the Mac says Offline or Printer not connected. Find the cause and re-add the printer so that it stays online.Guide →Double NAT: a mesh system behind your provider’s routerA mesh system behind your provider's router can create double NAT. See what it breaks, how to spot it from a Mac, and when to use bridge or passthrough mode.Guide →iCloud Private Relay and your router’s security or parental controlsPrivate Relay stops working at home, or your router's security and parental controls stop covering the Mac. See which router features conflict and what to change.Guide →

Sources

Checked on 10 November 2026.

See what your router can’t tell you

Kilobat is a Mac menu-bar app that watches the network from your side: which app is using it, whether the Wi-Fi, the router or the provider is slow, and why a call froze.

Download for Mac ↓
brew install seifip/kilobat/kilobat