Provider box · stc

stc modem login, Wi-Fi bands, restart and lights

stc supplies a modem with its fibre and DSL home lines. You manage it in a browser, and the address and sign-in depend on the model. stc’s own Modem Settings page lists them per model: look for the model number on the label on the back of your modem.

Sign in
192.168.100.1 or 192.168.1.1
Password
It depends on the model. The DZS ZNID 2428 B1 password is on a printed label on the ONT. The others use a fixed default that stc publishes (below). stc’s page doesn’t give the HG8245T sign-in details, though it refers to defaults. The E5577 MyFi uses 192.168.8.1.
Models
DZS ZNID 2428 B1, HG8245Q, HG8245T, G-240W-B, I-240W-A, HG658b, HG658v2, E5577 MyFi

Checked 10 November 2026. Paths checked in stc’s Modem Settings support page and its Wi-Fi configuration booklet, as of November 2026, for the DZS ZNID 2428 B1, HG8245Q, HG8245T, G-240W-B, I-240W-A, HG658b, HG658v2 and E5577 MyFi. stc documents no firmware versions. Lights and restart advice come from its Quick Solutions FAQ, mainly for DSL lines.

Sign in to the stc fibre and DSL modem

Factory default. From stc’s page. HG8245Q: telecomadmin and admintelecom. HG658b, HG658v2, G-240W-B, I-240W-A and E5577 MyFi: admin and admin. DZS ZNID 2428 B1: admin and the password on its label. Change a published default if your modem lets you.

  1. Check the model number on the label on the back of your modem.

  2. Connect your Mac to the modem. On the DZS ZNID 2428 B1, use an Ethernet cable to port GE1.

  3. On the DZS, HG8245Q or HG8245T, open 192.168.100.1 in a browser.

  4. On the HG658b, HG658v2, G-240W-B or I-240W-A, open 192.168.1.1 instead.

  5. Enter the username and password for your model and sign in.

stc’s HG8245T steps say that if you changed the credentials you should enter those instead. It documents no way to recover a forgotten modem password. Call 900 for help.

Restart it properly

  1. Turn the modem off and leave it off for at least 30 seconds.

  2. Turn it back on and let the connection resynchronise.

  3. Check the lights (see Status below).

stc also suggests restarting your computer and trying another browser if the modem looks fine. Don’t move the modem yourself once a fibre installer has placed it: stc asks you to call 900.

A full power cycle

stc’s device FAQ gives a longer version for a line that stays down.

  1. Turn the modem off.

  2. Unplug the phone cord from the wall and the modem, then the network cable and the power adapter.

  3. Wait five minutes, plug everything back in and turn the modem on.

  4. Check that the signal returns.

Schedule a restart

stc documents no scheduled restart.

Update the firmware

stc’s support pages give no firmware version, check or update steps for these modems.

See connected devices

stc’s support pages don’t describe a list of connected devices or a way to block one.

UPnP and port forwarding

stc’s support pages don’t document UPnP, port forwarding or NAT-PMP on these modems.

Prioritise calls and gaming

stc documents no QoS or device priority setting. It notes that several people online at once, game consoles and file-sharing programs all reduce your speed.

2.4 and 5 GHz, and the channel

stc’s booklet says 2.4 GHz is slower but reaches further, and 5 GHz is faster but shorter range, so you need to be closer to the modem. Set each band’s name and password separately.

stc also publishes short videos for several models, linked from its Modem Settings page.

HG8245Q (fibre)

  1. Sign in and open WLAN.

  2. Choose 2.4G Basic Network Settings or 5G Basic Network Settings.

  3. Type the name in Wireless Name and select WPA/WPA2 PreShared Key.

  4. Type the password in Pre-shared Key.

HG8245T (fibre)

  1. Sign in and open WLAN.

  2. Enter your own Wi-Fi name and make sure Wi-Fi is switched on.

  3. Choose WPA/WPA2/PRE and enter your own Wi-Fi password.

  4. Enter 3600, as stc’s steps say, then click Apply.

G-240W-B and I-240W-A (fibre)

  1. On the G-240W-B, open Network › Wireless (2.4 GHz). On the I-240W-A, open Network › WiFi.

  2. Set Encryption Mode to WPA/WPA2 Personal.

  3. Enter a WPA key of at least eight characters with letters and numbers.

  4. Click Save.

HG658b (DSL)

  1. Sign in, click Basic and select Wireless Settings.

  2. Set SSID (the name) and Shared Key (the password).

HG658v2 (DSL)

  1. Sign in, click Internet and select WLAN Settings.

  2. Click WLAN Encryption.

  3. Set the name, choose a security mode and enter the password in Pre-shared Key.

E5577 MyFi

  1. Go to 192.168.8.1, click Settings and sign in.

  2. Open WLAN › WLAN Basic Settings.

  3. Change the security mode to WPA/WPA2-PSK, and view or change the Wi-Fi password there.

Change the channel

stc says the default channel is 6 and suggests trying others in your wireless settings.

  1. On the HG658b, click Basic and select Wireless Settings.

  2. Select channel 1, 6 or 11.

stc gives channel steps only for the HG658b.

Mesh: which node a device uses

stc’s Fiber to every room service runs fibre from the main modem to up to 16 rooms, with a terminal in each. You request it by calling 900 or in mystc. Its home Wi-Fi solutions are chosen and fitted by an stc technician.

stc documents no pairing or setup steps you can do yourself.

Guest network

stc’s support pages don’t describe a guest Wi-Fi network on these modems.

DNS settings

stc’s support pages give no way to change the DNS servers. Set DNS on the Mac instead.

Connection status and logs

stc’s Quick Solutions FAQ reads the DSL modem’s lights. It calls the second light the CPE DSL light and the third the Internet light. It gives no light meanings for fibre modems.

  1. If the second light is red, restart the modem and move the line card connection from port 1 to port 2, or the reverse.

  2. If the second light is green and the third is red, check that your bill is paid.

  3. If it is paid, restart the modem and check the line status.

  4. If the connection keeps dropping and the lights flash, check that any splitter is connected properly.

  5. If it still fails, call 900.

stc’s fibre booklet says Wi-Fi speed also depends on the building, insulation, modem position and distance from it. The HG8245T steps add a VOICE page for the SIP phone line.

Set up the connection (WAN) on a fibre modem

  1. On the HG8245Q, sign in, open WAN and click New.

  2. Enter the username and password provided by stc.

  3. On the HG8245T, configure WAN for internet and click Apply.

No dial tone on fibre

  1. Check that the phone cable is in the right modem port or wall outlet (Tel1 or Tel2).

  2. Check that your modem supports fibre. Replace it if it doesn’t.

  3. Call 900 if you still have no dial tone.

Manuals and downloads

Links go to the maker’s own pages.

Questions

Which address does my stc modem use?

Check the model on the label. The DZS ZNID 2428 B1, HG8245Q and HG8245T use 192.168.100.1. The HG658b, HG658v2, G-240W-B and I-240W-A use 192.168.1.1. The E5577 MyFi uses 192.168.8.1.

My stc 5G router is asking for a PIN. What do I do?

Put the SIM in the router and enter a wrong PIN three times until it asks for the PUK. Enter the PUK and set the new SIM PIN to 0000. On your phone, open Settings › Mobile Network › SIM PIN, disable it and enter 0000. Reinsert the SIM in the router and wait five minutes.

Should I use 2.4 GHz or 5 GHz?

stc suggests 5 GHz for high use such as online games and film downloads, when you’re near the modem. It suggests 2.4 GHz when you don’t need high speed and want wider coverage in the home.

Mac problems on this network

Fixes for what Mac users most often hit on home routers and mesh systems.

Mac drops Wi-Fi or sticks to a far node on mesh Wi-FiOn a mesh network, your Mac drops when it moves between nodes, or stays on a distant one. See how Macs roam and which router settings to change.Guide →Mac Wi-Fi keeps disconnectingYour Mac drops Wi-Fi again and again, not only after sleep. Record when the drops happen, then check the router, roaming, interference and network software.Guide →Mac won't connect to a WPA3 or Wi-Fi 7 routerYour Mac can't join, or keeps dropping, after the router moved to WPA3 or Wi-Fi 7. Check the security mode, PMF and MLO, and the saved network.Guide →Mac can't see or join a 6 GHz Wi-Fi networkYour Mac never uses 6 GHz, or can't find the 6 GHz network. Check Mac support, Wi-Fi 6E mode, WPA3 and the router's 6 GHz settings.Guide →AirPlay or AirPrint stopped working after a new router or meshYour Mac no longer finds the Apple TV, speaker or printer after a router or mesh change. Check the router settings that stop Bonjour discovery, brand by brand.Guide →Wi-Fi printer shows Offline on a MacThe printer is on and connected to Wi-Fi, but the Mac says Offline or Printer not connected. Find the cause and re-add the printer so that it stays online.Guide →Double NAT: a mesh system behind your provider’s routerA mesh system behind your provider's router can create double NAT. See what it breaks, how to spot it from a Mac, and when to use bridge or passthrough mode.Guide →iCloud Private Relay and your router’s security or parental controlsPrivate Relay stops working at home, or your router's security and parental controls stop covering the Mac. See which router features conflict and what to change.Guide →

Sources

Checked on 10 November 2026.

See what your router can’t tell you

Kilobat is a Mac menu-bar app that watches the network from your side: which app is using it, whether the Wi-Fi, the router or the provider is slow, and why a call froze.

Download for Mac ↓
brew install seifip/kilobat/kilobat