Provider box · PLDT

PLDT Home modem login, restart, Wi-Fi password and guest Wi-Fi

PLDT supplies Fibr and DSL modems with its home plans, and LTE PLDT Home WiFi units for prepaid wireless. You manage them in a browser at 192.168.1.1; the FX-ID4 also has a mobile app.

Sign in
192.168.1.1 or pldthomewifisettings.net
App
Evoluzn FX-ID4 Home WiFi, search “FXID4” (iOS and Android)
Password
PLDT says the default username and password are at the back of the modem or under it. The FX-ID4’s label shows its Wi-Fi name, and its first Wi-Fi password is pldthome.
Models
PLDT Home Fiber modem, PLDT Home DSL modem, PLDT Home WiFi FX-ID4, Fiberhome HG6245D, Fiberhome HG180U2, Huawei HG8145V5, ZTE H188A, Evoluzn FX-ID7, Greenpacket D2K-FT50, Boosteven R221s, Huawei H151-370

Checked 10 November 2026. Fibr and DSL paths are from PLDT’s support pages and customer user guide, which name no firmware version and vary by modem brand. Home WiFi paths were checked in PLDT’s guides for the FX-ID4 (app version 1.1.4). For the FX-ID7, D2K-FT50, R221s and H151-370, PLDT documents only the factory reset.

Sign in to the PLDT Home modem

Factory default. Fibr and DSL modems: username admin, password 1234. FX-ID4: username pldthome, password pldthome. Change the password when the first login asks you to.

  1. Connect your Mac to the modem’s Wi-Fi or to a LAN port by cable.

  2. Open https://192.168.1.1 in a browser. An FX-ID4 also answers at pldthomewifisettings.net.

  3. On an FX-ID4, if a certificate warning appears, click Advanced, then Proceed.

  4. Type the username and password.

  5. On first login, set a new password when prompted. Fibr modems show this under Account Management.

PLDT’s printed guide calls the Fibr pages Setup › Basic and Security Setting instead. On the FX-ID4, new admin and Wi-Fi passwords need at least 12 characters with upper and lower case, digits and symbols. Forgotten the password? Hold the reset pinhole for five seconds on a Fibr modem. Its factory logins then work again, and your settings are lost.

Change the Wi-Fi name on a Fibr modem

  1. Open Basic › Wireless LAN (WLAN) Settings.

  2. Type the new name in SSID Name.

  3. Click Apply Changes, then save.

Change the Wi-Fi password on a Fibr modem

  1. Open Wireless LAN (WLAN) Settings › Security.

  2. Set Encryption/Security Mode to WPA2-MIXED.

  3. Type the new password in Pre-shared Key.

  4. Reconnect your devices with the new password.

Change the Wi-Fi name and password on an FX-ID4

  1. Open Settings › Basic Settings › WiFi Settings.

  2. Enter the new name, without spaces, and the new password.

  3. Click Apply, then reconnect to the new network.

Restart it properly

  1. Turn the Fibr or DSL modem off for five minutes.

  2. Turn it back on and allow three minutes for it to sync.

  3. Check that the lights match the list under status below.

PLDT’s two FX-ID4 guides give different reset-button times: 10 seconds in the Web UI guide and 6 seconds in the app guide.

Restart the modem online

PLDT’s Device Management tool can restart your modem remotely.

  1. Open the Device Management page and click Start Now.

  2. Enter your PLDT account number and telephone number to verify yourself.

  3. Choose Modem Restart.

Restart an FX-ID4

  1. Sign in and open Settings › Basic Settings.

  2. Click the button under Device Reboot.

Factory reset a Home WiFi unit

  1. FX-ID4: use Settings › Basic Settings › Factory Reset › Restore.

  2. FX-ID7: use Settings › Router Management › Reset, or hold RST for 6 seconds.

  3. D2K-FT50: use Settings › Router Management › Restore, or hold RST for 10 seconds.

  4. R221s: use Settings › Router Management › Restore, or hold RST for 8 seconds.

  5. H151-370: use Advanced › System › Reset, or hold RST for 6 seconds.

Schedule a restart

PLDT documents no scheduled restart.

Update the firmware

The FX-ID4 updates itself. While it does, every light except Power blinks for five to six minutes. Leave it switched on until it restarts.

PLDT documents no firmware version page, manual update or download for any of its modems.

See connected devices

PLDT documents a device list only for the FX-ID4.

  1. Sign in and open the Status tab.

  2. Open Active Device List to see what is connected.

Rename or block a device in the FX-ID4 app

  1. Under Connected Devices, tap a device and type a new name.

  2. To block it, press its toggle switch and confirm with Block.

  3. To unblock it, press the same switch under Blocked Devices.

Limit a device’s hours on an FX-ID4

  1. Open Settings › Advanced Settings › Parent Ctrl.

  2. Set Status to Enable.

  3. Click Add New in the Time Rule table.

  4. Choose the device, then the times and days it may go online.

  5. Click Apply.

UPnP and port forwarding

PLDT’s support pages and guides don’t mention UPnP, NAT-PMP or port forwarding on any of its modems.

Prioritise calls and gaming

PLDT documents no QoS or device priority setting. For slow connections, it suggests limiting how many devices are online.

2.4 and 5 GHz, and the channel

PLDT lists these Fiber and DSL modems as dual-band: Zyxel VMG3926-B10B, Baudtec RN104R4GC-A5, Unit Power RN104R4GC-2T2R-A5b, Prolink PRS1841U-V2, Fiberhome HG180U2 and HG6245D, ZTE H188A and Huawei HG8145V5. They don’t steer devices between bands, so you pick one yourself.

  1. Open your device’s Wi-Fi list. Both bands appear as separate names.

  2. Choose 5 GHz for a device that stays near the modem.

  3. Choose 2.4 GHz for a device that moves around the home.

PLDT recommends 2.4 GHz up to 150 feet indoors and 5 GHz up to 50 feet.

Change the channel

PLDT documents no way to choose a Wi-Fi channel.

Mesh: which node a device uses

PLDT sells TP-Link Deco and Tenda Nova mesh units. You need at least two: one connected to the modem and one where the signal is weak.

  1. Install the TP-Link Deco or Tenda Nova app, depending on your units.

  2. Turn on Wi-Fi and GPS on your phone.

  3. Connect the first unit to your Fiber modem.

  4. Follow the app’s steps to add the other units.

Add a satellite to an FX-ID4

  1. Finish the setup steps in the FX-ID4 app.

  2. On the Enable Mesh screen, tap Enable and add the satellite.

  3. If you have no satellite, tap Done instead.

Guest network

PLDT documents guest Wi-Fi only on the FX-ID4. Fibr modems have no documented guest network.

  1. Sign in and open Settings › Basic Settings › Guest WiFi Settings.

  2. Click Add New. You can have up to four guest networks.

  3. Set the guest network’s name and password.

  4. Click Apply.

In the FX-ID4 app

  1. Tap Settings › Guest WiFi.

  2. Set the name and password, then wait about 30 seconds.

DNS settings

PLDT documents no way to change the DNS servers. The FX-ID4 dashboard shows the provider’s DNS server in use. Set DNS on the Mac instead.

Connection status and logs

On a working Fibr modem, Power and PON are solid green, LOS is off and WLAN pulses green.

  1. If Power is orange or red, turn the modem off for five minutes, then back on.

  2. If LOS is red or blinking, check that the fibre cable is seated properly.

  3. If PON is off or blinking, check the fibre at the modem and the wall outlet.

  4. If PON is steady green, the modem is connected. Try a website.

On Fibr modems, LAN1 is for internet, LAN2 and LAN3 for add-on services or Cignal, and LAN4 for Cignal only. If the FX-ID4’s Internet light is blue, it is online.

DSL modems

  1. If DSL is off or blinking, check for loose or damaged cables.

  2. Replug the telephone cable from the modem’s DSL port to the splitter.

  3. If Internet is off or red, turn the modem off for five minutes.

FX-ID4 status

  1. Open the Dashboard tab for the network operator, connection status, WAN IP and DNS.

  2. Open the Status tab for WAN, Wi-Fi and device information.

Run a remote test

  1. On the Device Management page, run Speed/Ping Test.

  2. Use Heal for slow browsing and Refresh to update connected devices and speed.

Manuals and downloads

Links go to the maker’s own pages.

Questions

Where do I find the default PLDT Wi-Fi details?

At the back of the modem or under it. On an FX-ID4, the label also has a Wi-Fi QR code.

How do I see the Wi-Fi password on an FX-ID4?

Open the FX-ID4 app and press Reveal WiFi on the home page.

Mac problems on this network

Fixes for what Mac users most often hit on home routers and mesh systems.

Mac drops Wi-Fi or sticks to a far node on mesh Wi-FiOn a mesh network, your Mac drops when it moves between nodes, or stays on a distant one. See how Macs roam and which router settings to change.Guide →Mac Wi-Fi keeps disconnectingYour Mac drops Wi-Fi again and again, not only after sleep. Record when the drops happen, then check the router, roaming, interference and network software.Guide →Mac won't connect to a WPA3 or Wi-Fi 7 routerYour Mac can't join, or keeps dropping, after the router moved to WPA3 or Wi-Fi 7. Check the security mode, PMF and MLO, and the saved network.Guide →Mac can't see or join a 6 GHz Wi-Fi networkYour Mac never uses 6 GHz, or can't find the 6 GHz network. Check Mac support, Wi-Fi 6E mode, WPA3 and the router's 6 GHz settings.Guide →AirPlay or AirPrint stopped working after a new router or meshYour Mac no longer finds the Apple TV, speaker or printer after a router or mesh change. Check the router settings that stop Bonjour discovery, brand by brand.Guide →Wi-Fi printer shows Offline on a MacThe printer is on and connected to Wi-Fi, but the Mac says Offline or Printer not connected. Find the cause and re-add the printer so that it stays online.Guide →Double NAT: a mesh system behind your provider’s routerA mesh system behind your provider's router can create double NAT. See what it breaks, how to spot it from a Mac, and when to use bridge or passthrough mode.Guide →iCloud Private Relay and your router’s security or parental controlsPrivate Relay stops working at home, or your router's security and parental controls stop covering the Mac. See which router features conflict and what to change.Guide →

Sources

Checked on 10 November 2026.

See what your router can’t tell you

Kilobat is a Mac menu-bar app that watches the network from your side: which app is using it, whether the Wi-Fi, the router or the provider is slow, and why a call froze.

Download for Mac ↓
brew install seifip/kilobat/kilobat